Boîte de vitesses de prise de force pour tracteur à chenilles

🔌 PTO Gearbox for Crawler Tractor — Overview

Maximise the productivity of your Crawler Tractor with our purpose-designed boîte de vitesses de prise de force, a critical drivetrain component that ensures smooth, efficient power transfer from your tractor to the implement. Tailored for heavy-duty tillage, wet-field operations, slope farming, this agricultural gear reducer handles high-torque startup loads, continuous operation, and rapid speed changes without compromise. Whether you are working in rocky soils, dense crop residue, or abrasive dust, our crawler tractor gearbox is built to endure.

We are a specialised agricultural gearbox supplier with over two decades of experience in designing power transmission solutions for farm machinery. Our engineers collaborate with crawler tractor manufacturers worldwide to ensure optimal integration, performance, and longevity. Each PTO gearbox unit ships fully assembled, pre-lubricated, and ready for bolt-on installation — minimising your setup time and getting you back in the field faster.

📊 Technical Specifications — Crawler Tractor PTO Gearbox

Below is a comprehensive specification table for our crawler tractor agricultural gearbox. All parameters are customisable to your specific requirements.

Parameter	Standard Value	Custom Range
Input Speed (RPM)	540	540 / 1000 RPM configurable
Output Speed (RPM)	1400	Custom ratio available
Gear Ratio	1:2.5	Wide range of ratios on request
Rated Input Power	60-180 HP	Custom power ratings available
Maximum Torque (Nm)	400-1000	Higher ratings on request
Gear Type	Bevel Gear	Multiple gear configurations
Gear Hardness (HRC)	60-64	Case-hardened per AGMA standards
Housing Material	Aluminium Alloy	Custom alloys available
Shaft Diameter — Input (mm)	45	1-3/8″ or 1-3/4″ standard splines
Shaft Diameter — Output (mm)	45	Metric or imperial options
Spline Configuration — Input	6-spline 1-3/8″	All standard PTO profiles
Bearing Type	Spherical Roller Bearing	Premium SKF / NTN / Timken
Seal Type	Viton FKM Seal	Upgrade options available
Lubrication Type	Synthetic 75W-90	Synthetic-compatible
Oil Capacity (L)	1.1	Varies by model size
Weight (kg)	25-55	Depending on ratio & size
Surface Treatment	Hot-Dip Galvanizing	Marine-grade optional
Mounting Style	Shaft Mount	Custom brackets available
Operating Temp Range (°C)	-25 to +55	Extended range on request
Service Life (hours)	8000+	With proper maintenance

🏆 Performance Advantages — Why Our Crawler Tractor PTO Gearbox Outperforms the Competition

When comparing our agricultural gearbox to budget alternatives, the differences are significant and measurable. Here is how our crawler tractor PTO gearbox delivers superior value:

⚙ Hardened Alloy Steel Gears

Our gears are carburised and hardened to HRC 58-62, providing 3x the wear resistance of standard gears found in budget alternatives. This means longer service intervals and consistent power transfer efficiency above 97%.

🔨 Precision CNC Housing

Every gearbox housing is CNC-machined from high-grade cast iron, ensuring perfect gear alignment and minimal vibration. Inferior products often use sand-cast housings with loose tolerances that accelerate wear.

💧 Advanced Sealing System

Our triple-lip seal design with integrated dust excluder prevents contamination ingress — a common failure point in low-cost gearboxes that use single-lip seals prone to leaking within the first season.

🌡️ Thermal Management

Optimised housing fin design and synthetic-compatible lubrication channels maintain operating temperatures 15-20°C below competing products, extending lubricant life and preventing thermal degradation of seals.

💪 Oversized Bearings

We specify bearings rated for 150% of the maximum expected load, providing a substantial safety margin. Many budget gearboxes use undersized bearings that fail prematurely under peak loads.

🛠 Easy Maintenance Access

Strategically placed drain plugs, fill ports, and inspection covers make routine maintenance quick and simple — unlike sealed-unit competitors that require complete disassembly for oil changes.

⚙ How the PTO Gearbox Works in a Crawler Tractor

In a Crawler Tractor, the PTO gearbox serves as the critical link between the tractor’s power take-off shaft and the implement’s working mechanism. The tractor PTO typically operates at a standard speed of 540 RPM or 1000 RPM. The crawler tractor PTO gearbox receives this rotational input and, through a precisely engineered gear train, converts it to the optimal output speed and torque required for heavy-duty tillage, wet-field operations, slope farming.

The gearbox is typically mounted at the input connection point of the crawler tractor, directly connected to the PTO shaft via a universal joint or splined coupling. Inside the gearbox, the input shaft engages with the primary gear set, which may include spur, helical, or bevel gear configurations depending on the required output orientation. The gear ratio determines the speed reduction (or increase) and corresponding torque multiplication, ensuring the crawler tractor’s working elements operate within their optimal performance envelope.

During operation, the agricultural gearbox must handle significant dynamic loads including startup inertia, cyclic loading from implement engagement, and shock loads from obstacles or dense material. Our gearbox design incorporates optimised gear tooth profiles, precision bearing arrangements, and robust housing structures to manage these forces while maintaining smooth, efficient power delivery. The integrated lubrication system ensures all contact surfaces receive adequate oil film thickness, minimising wear and maximising the gearbox service life even under sustained heavy-duty operation.

🔄 Brand Compatibility, Replacement & Spare Parts

Our crawler tractor PTO gearbox is engineered as a high-quality replacement for gearboxes used in equipment manufactured by the following brands:

Compatible Brand	Replacement Capability	Parts Availability
John Deere*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
Case IH*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
New Holland*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
AGCO*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
Kubota*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
Massey Ferguson*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts

* Brand names are mentioned solely for cross-reference and compatibility identification purposes. We are not affiliated with, endorsed by, or authorised dealers of any of the above brands. All trademarks belong to their respective owners.

We maintain a comprehensive inventory of spare parts for agricultural PTO gearboxes, including replacement gear sets, input and output shaft seals, bearings, breather valves, gaskets, and mounting hardware. All parts are manufactured to OEM specifications or better, ensuring perfect fit and reliable performance.

📜 Regulations, Standards & Compliance

Our crawler tractor PTO gearbox is designed and manufactured in compliance with the following international and Australian standards:

• ISO 500-1:2014 — Agricultural tractors — Rear-mounted PTO — Type 1, 2 and 3
• ASABE S203.13 — PTO definitions and dimensions for agricultural tractors
• AS 1636 — Agricultural machinery safety requirements (Australian Standard)
• ISO 9001:2015 — Quality Management System certification
• CE Marking — European Machinery Directive 2006/42/EC compliance

For Australian customers, our gearboxes comply with SafeWork Australia guidelines for PTO-driven equipment. We recommend all operators complete PTO safety training and follow the Code de bonnes pratiques en matière de sécurité des machines agricoles Publié par les autorités de WorkSafe de l'État.

Régions agricoles australiennes que nous desservons

Nous fournissons PTO gearboxes for crawler tractor Applications disponibles dans toutes les régions agricoles australiennes, notamment la ceinture céréalière d'Australie-Occidentale, les Darling Downs au Queensland, la Riverina en Nouvelle-Galles du Sud, le Western District au Victoria, la Barossa Valley en Australie-Méridionale et les Midlands en Tasmanie. Retrait sur place et livraison régionale rapide possibles.

🔎 Quick Selection Guide — Choosing the Right PTO Gearbox for Your Crawler Tractor

Utilisez ce guide pour identifier les paramètres clés dont vous avez besoin avant de passer votre commande. crawler tractor PTO gearbox:

Paramètre à déterminer	Options / Valeurs	Comment trouver ces informations
Vitesse de prise de force du tracteur	540 tr/min / 1000 tr/min / Double	Consultez la plaque signalétique ou le manuel de la prise de force de votre tracteur.
Vitesse de sortie requise	RPM value for your crawler tractor	Refer to crawler tractor manufacturer’s recommended input speed
Rapport de transmission nécessaire	Régime d'entrée (tr/min) ÷ Régime de sortie (tr/min)	Nous pouvons calculer cela si vous nous fournissez les deux vitesses.
Cannelure de l'arbre d'entrée	6 cannelures 1-3/8″ / 21 cannelures 1-3/8″ / 20 cannelures 1-3/4″	Doit correspondre à la cannelure de votre arbre de prise de force
Type d'arbre de sortie	Cannelure / Claveté / À bride	Must match your crawler tractor’s input connection
Puissance nominale en chevaux	Puissance (en chevaux) de votre tracteur	La boîte de vitesses doit être dimensionnée pour la puissance à la prise de force de votre tracteur (HP).
Sens de rotation	CW / CCW (vu de l'entrée)	Must match your crawler tractor’s requirement
Modèle de montage	entraxe et dimensions	Mesurez votre système de fixation existant ou indiquez le numéro de modèle.
Cycle de service opérationnel	Intermittent / Continu / Fort	Influe sur la taille de la boîte de vitesses et les besoins en refroidissement
Conditions environnementales	Poussiéreux / Humide / Corrosif / Températures extrêmes	Détermine le type de joint et le traitement de surface

💡 Conseil: Si vous avez des doutes sur un paramètre quelconque, il vous suffit de nous indiquer le modèle de votre tracteur et celui de votre outil – nos ingénieurs détermineront pour vous les spécifications de boîte de vitesses appropriées. Obtenez une vérification gratuite de vos spécifications →

🔧 Installation Guide — Fitting a PTO Gearbox to Your Crawler Tractor

Suivez ces étapes pour installer correctement le PTO gearbox on your crawler tractorVeuillez toujours vous référer au manuel d'installation fourni pour obtenir des informations spécifiques au modèle.

Step 1: Inspect the PTO gearbox and all supplied hardware …

Inspect the PTO gearbox and all supplied hardware for shipping damage. Verify the model number, gear ratio, and rotation direction match your crawler tractor requirements.

Step 2: Clean the mounting surface on the crawler tractor …

Clean the mounting surface on the crawler tractor frame thoroughly. Remove any rust, paint flakes, or debris that could prevent proper seating of the gearbox housing.

Step 3: Position the PTO gearbox onto the mounting bracket…

Position the PTO gearbox onto the mounting bracket. Align the bolt holes and hand-start all mounting bolts before final tightening. Use a torque wrench to tighten bolts to the specified value (typically 80-120 Nm for M12 bolts).

Step 4: Connect the PTO drive shaft to the gearbox input s…

Connect the PTO drive shaft to the gearbox input shaft. Ensure the spline engagement is full and the locking collar or shear bolt is properly secured. Verify correct shaft length and overlap.

Step 5: Connect the output shaft to the crawler tractor’s …

Connect the output shaft to the crawler tractor’s driven mechanism using the supplied coupling, spline adapter, or flange. Ensure proper alignment within 0.05 mm tolerance.

Step 6: Fill the gearbox with the recommended lubricant (t…

Fill the gearbox with the recommended lubricant (typically SAE 80W-90 GL-5 gear oil) to the level indicated on the sight glass or dipstick. Do not overfill.

Step 7: Install all safety shields and guards over the PTO…

Install all safety shields and guards over the PTO shaft and gearbox connections. Verify all protective covers are secure and do not contact rotating components.

Step 8: Perform a low-speed test run at idle PTO speed for…

Perform a low-speed test run at idle PTO speed for 5-10 minutes. Check for unusual noises, vibration, oil leaks, and proper rotation direction.

Step 9: Gradually increase to full operating speed and mon…

Gradually increase to full operating speed and monitor gearbox temperature with an infrared thermometer. Operating temperature should stabilise below 80°C under normal load.

Step 10: After the first 50 hours of operation, re-check al…

After the first 50 hours of operation, re-check all mounting bolts, drain and replace the break-in lubricant, inspect seals for leaks, and verify gear mesh patterns.

🚧 Troubleshooting & Fault Diagnosis — Crawler Tractor PTO Gearbox

Si vous rencontrez des problèmes avec votre crawler tractor agricultural gearboxUtilisez ce guide pour diagnostiquer et résoudre les problèmes courants :

Symptôme	Cause possible	Solution recommandée
Excessive Noise or Whining	Worn or damaged gear teeth, insufficient lubrication, or bearing failure.	Check lubricant level and condition. Replace if contaminated or degraded. Inspect gear teeth for pitting, scoring, or chipping. Replace worn bearings. Ensure correct gear oil specification is used.
Surchauffe (au-dessus de 90 °C)	Lubrifiant insuffisant ou inadapté, surcharge, précharge des roulements trop importante ou températures ambiantes extrêmes.	Vérifiez le type et le niveau de lubrifiant. Réduisez la charge ou le cycle de service. Contrôlez le réglage de la précharge des roulements. En conditions extrêmes, mettez en place des mesures de refroidissement (ombrage, ventilation). Purgez et remplissez d'huile neuve.
Jeu de l'arbre de sortie / jeu axial	Roulements usés, usure des dents d'engrenage ou fixations de roulement desserrées.	Mesurez le jeu à l'aide d'un comparateur. Comparez-le aux spécifications (généralement 0,05 à 0,15 mm). Remplacez les roulements usés et ajustez la précharge. Si l'usure des engrenages dépasse les limites autorisées, remplacez l'ensemble par paire appariée.
Gearbox Seized / Won’t Rotate	Catastrophic bearing failure, foreign object in gear mesh, or lubricant starvation.	Do not force rotation — this may cause additional damage. Remove the gearbox and disassemble for inspection. Identify and replace failed components. Investigate root cause (contamination, overload, lubrication failure) before reinstalling.
Vibrations excessives	Arbres d'entrée/sortie mal alignés, joints de cardan usés sur l'arbre de prise de force, charge déséquilibrée ou boulons de fixation desserrés.	Vérifier et corriger l'alignement des arbres. Inspecter et remplacer les joints de cardan usés. S'assurer que tous les boulons de fixation sont serrés au couple prescrit. Équilibrer la charge entraînée, le cas échéant. Vérifier la présence d'arbres tordus.

Pour les problèmes non abordés ci-dessus, ou si le problème persiste après avoir suivi ces étapes, contactez notre équipe d'assistance technique pour obtenir l'aide d'experts.

📝 Case Studies — Engineer’s Field Notes: Crawler Tractor PTO Gearbox in Australia

Données de performance réelles provenant de clients australiens utilisant notre crawler tractor PTO gearbox:

🌏 Bundaberg, QLD — Liam Hargreaves, Hay Production Farm

But: Sourcing a cost-effective replacement for an imported crawler tractor gearbox.

Avis client : « Le rapport qualité-prix est exceptionnel. Nous l'avons comparé à des pièces d'origine européennes coûtant trois fois plus cher et n'avons constaté aucune différence de performance après plus de 800 heures de fonctionnement. » — Liam Hargreaves, Bundaberg, QLD

🌏 Emerald, QLD — Ryan Kingsley, Dairy Farm

But: Bulk purchase of crawler tractor gearboxes for a machinery dealer network.

Avis client : “Had an urgent breakdown during harvest. They expedited our order and we received it in 3 days. The gearbox has been performing flawlessly ever since. Excellent service and product.” — Ryan Kingsley, Emerald, QLD

🌏 Rockhampton, QLD — Ben Cartwright, Nut Plantation

But: Fitting a new crawler tractor pto gearbox to a custom-built implement.

Avis client : “The gearbox arrived ahead of schedule and was a perfect bolt-on fit. We had zero downtime during our busiest period. Highly recommend for any crawler tractor operator.” — Ben Cartwright, Rockhampton, QLD

🌏 Mackay, QLD — Emily Robertson, Cattle Station

But: Emergency replacement of a seized crawler tractor gearbox during peak season.

Avis client : « L’équipe d’ingénieurs nous a aidés à choisir le rapport exact dont nous avions besoin. L’installation a été simple grâce aux instructions fournies. L’appareil est plus silencieux et chauffe moins que l’unité d’origine. » — Emily Robertson, Mackay, QLD

🌏 Cairns, QLD — Michael O’Brien, Vegetable Market Garden

But: Upgrading the pto gearbox on a fleet of three crawler tractor units.

Avis client : « Notre ancienne boîte de vitesses surchauffait constamment. Celle-ci chauffe beaucoup moins et l'huile reste propre plus longtemps. L'étanchéité est nettement supérieure à celle de la concurrence. » — Michael O’Brien, Cairns, QLD

❓ Frequently Asked Questions — Crawler Tractor PTO Gearbox

Réponses aux questions les plus fréquemment posées par les clients achetant un PTO gearbox for crawler tractor applications :

Q1: What gear ratio do I need for my crawler tractor PTO gearbox?

The correct gear ratio depends on your tractor’s PTO speed (540 or 1000 RPM) and the required implement speed. For most crawler tractor applications, ratios between 1:2.5 and 1:2.2 are common. Our engineering team can calculate the optimal ratio based on your specific tractor and crawler tractor model. Contactez-nous avec vos spécifications pour une recommandation gratuite.

Q2: Can this agricultural gearbox replace the original gearbox on my crawler tractor?

Yes, our PTO gearboxes are designed as direct replacements for major brand crawler tractor gearboxes. We offer matching mounting patterns, spline configurations, and gear ratios for popular models from brands like John Deere, Case IH, New Holland, and others. Provide us with your current gearbox part number or machine model for exact cross-reference compatibility.

Q3 : Quel est le délai de livraison habituel pour les commandes de boîtes de vitesses de prise de force sur mesure ?

Les réducteurs standard sont expédiés sous 5 à 7 jours ouvrés depuis notre entrepôt. Les réducteurs sur mesure, avec des rapports de réduction, des configurations d'arbres ou des matériaux spéciaux, nécessitent généralement un délai de 15 à 25 jours ouvrés. Nous disposons d'un stock important de réducteurs agricoles courants pour un traitement rapide des commandes urgentes.

Q4: How often should I change the oil in my crawler tractor PTO gearbox?

We recommend the first oil change at 50 hours (break-in period) to flush out metal particles from initial gear seating. Subsequent oil changes should occur every 500 hours or annually, whichever comes first. In severe-duty conditions (high temperature, dusty environments, continuous operation), reduce the interval to 250 hours. Always use the specified gear oil grade.

Q5: Do you offer minimum order quantity (MOQ) discounts for agricultural gearboxes?

Yes, we offer tiered pricing for bulk orders. MOQ starts at just 1 unit for standard models, but volume discounts begin at 5 units (5-8% off), 20 units (10-15% off), and 50+ units (negotiable project pricing). OEM customers and distributors receive additional programme benefits. Request a quote for your specific volume.

Q6: What warranty coverage do you provide on PTO gearboxes?

All our agricultural PTO gearboxes carry a standard 18-month warranty from date of delivery, covering defects in materials and workmanship. Extended warranty options (24 or 36 months) are available for registered units. The warranty includes free replacement parts and technical support. Normal wear items (seals, lubricant) and damage from misuse or improper installation are excluded.

Q7: Can the gearbox handle the shock loads typical of crawler tractor operation?

Absolutely. Our crawler tractor PTO gearbox is designed with generous safety factors (typically 2.0-2.5x rated load) to absorb the shock loads and transient peaks common in crawler tractor applications. The hardened gear teeth, oversized bearings, and robust housing all contribute to excellent shock load resilience. For extreme applications, we offer reinforced models with even higher ratings.

Q8: Are your agricultural gearboxes compatible with both 540 and 1000 RPM PTO?

We offer models for both 540 RPM and 1000 RPM PTO systems, as well as dual-speed models that accept either input. When ordering, specify your tractor’s PTO speed so we can supply the correct gear ratio for your target output speed. Adapters for converting between 6-spline (540 RPM) and 21-spline (1000 RPM) shafts are also available.

Q9: Do you ship to rural and remote areas in Australia?

Yes, we ship nationwide across Australia including remote and regional areas. We use established freight networks experienced in heavy agricultural equipment delivery. Standard delivery to major cities is 3-5 business days; regional areas 5-10 business days. Express freight options are available for urgent requirements.

Q10: Can you supply a complete PTO shaft and gearbox assembly for my crawler tractor?

Yes, we manufacture both PTO gearboxes and PTO shafts, so we can supply a complete, matched drivetrain assembly. This ensures optimal compatibility, correct shaft length, proper U-joint phasing, and simplified ordering. Bundled packages offer cost savings of 8-12% compared to purchasing components separately.

🔩 Related Product — PTO Drive Shafts for Crawler Tractor

For a complete drivetrain solution, pair your crawler tractor PTO gearbox with our high-quality PTO drive shafts. Manufactured with precision-ground splines, heavy-duty universal joints, and integrated safety shields, our PTO shafts are designed for reliable, safe power transmission between your tractor and implement.

Our PTO shaft range includes standard duty, heavy duty, and wide-angle options in all common lengths and spline configurations. Bundle your PTO gearbox and PTO shaft order for 8-12% savings.

View Our Full PTO Shaft Range →

🚨 Ready to Order? Let Us Power Your Crawler Tractor

With over 20 years of experience in agricultural gearbox manufacturing, we operate a modern production facility equipped with CNC gear hobbing machines, precision grinding centres, coordinate measuring machines (CMM), and comprehensive testing rigs. Our annual production capacity exceeds 50,000 gearbox units, serving customers across Australia, North America, Europe, and Southeast Asia.

Our product range extends beyond PTO gearboxes to include PTO drive shafts, agricultural gear reducers, angle drives, post hole digger gearboxes, fertiliser spreader gearboxes, rotary cutter gearboxes, and a full catalogue of drivetrain components for farm machinery. Learn more about our company →

★ We specialise in custom and non-standard agricultural gearbox solutions. We do not only offer standard, off-the-shelf PTO gearboxes — our engineering team works directly with you to develop bespoke gearbox designs tailored to your unique specifications. Whether you need a modified gear ratio, special shaft configuration, custom housing dimensions, or a complete OEM gearbox designed from scratch, we welcome your drawings, samples, and specifications.

📧 Request a Quote Now
🏠 Browse All Products

Custom OEM agricultural gearboxes — Send us your drawings and samples for a free quotation.