Boîte de vitesses à prise de force pour ensileuse

🔌 PTO Gearbox for Forage Harvester / Silage Harvester — Overview

Power your Forage Harvester / Silage Harvester with confidence using our precision-engineered boîte de vitesses de prise de force, designed from the ground up for the unique demands of silage making, forage chopping, feed preparation. This robust agricultural gearbox converts PTO rotational energy into the exact speed and torque profile your forage harvester / silage harvester requires, optimising both performance and fuel efficiency. Manufactured in our state-of-the-art facility with advanced CNC and gear-grinding technology, every unit meets exacting tolerances.

What sets our forage harvester / silage harvester gearbox apart is the attention to real-world agricultural conditions. We account for shock loads, debris ingestion risks, temperature extremes, and extended duty cycles in our design process. The result is a PTO gear drive that outperforms and outlasts competing products, backed by comprehensive technical support and a robust warranty programme. Join thousands of satisfied agricultural professionals who trust our farm machinery gearbox solutions.

📊 Technical Specifications — Forage Harvester / Silage Harvester PTO Gearbox

Below is a comprehensive specification table for our forage harvester / silage harvester agricultural gearbox. All parameters are customisable to your specific requirements.

Parameter	Standard Value	Custom Range
Input Speed (RPM)	540/1000	540 / 1000 RPM configurable
Output Speed (RPM)	540	Custom ratio available
Gear Ratio	2:1	Wide range of ratios on request
Rated Input Power	50-150 HP	Custom power ratings available
Maximum Torque (Nm)	700-1800	Higher ratings on request
Gear Type	Hypoid Gear	Multiple gear configurations
Gear Hardness (HRC)	59-64	Case-hardened per AGMA standards
Housing Material	Aluminium Alloy	Custom alloys available
Shaft Diameter — Input (mm)	45	1-3/8″ or 1-3/4″ standard splines
Shaft Diameter — Output (mm)	35	Metric or imperial options
Spline Configuration — Input	6-spline 1-3/4″	All standard PTO profiles
Bearing Type	Tapered Roller Bearing	Premium SKF / NTN / Timken
Seal Type	Double-lip NBR Seal	Upgrade options available
Lubrication Type	Synthetic 75W-90	Synthetic-compatible
Oil Capacity (L)	1.7	Varies by model size
Weight (kg)	38-72	Depending on ratio & size
Surface Treatment	Hot-Dip Galvanizing	Marine-grade optional
Mounting Style	Foot Mount	Custom brackets available
Operating Temp Range (°C)	-25 to +55	Extended range on request
Service Life (hours)	15000+	With proper maintenance

🏆 Performance Advantages — Why Our Forage Harvester / Silage Harvester PTO Gearbox Outperforms the Competition

When comparing our agricultural gearbox to budget alternatives, the differences are significant and measurable. Here is how our forage harvester / silage harvester PTO gearbox delivers superior value:

⚙ Aerospace-Derived Metallurgy

Gear sets are manufactured from vacuum-degassed 8620H alloy steel, then carburised and precision-ground to AGMA Class 11 quality — exceeding the AGMA Class 8-9 found in most agricultural gearboxes.

🔬 Finite Element Optimised

Every housing design is validated through FEA stress analysis and modal analysis to eliminate resonance and stress concentration points — a level of engineering rigour absent from mass-produced budget alternatives.

💧 Synthetic Lubricant Ready

Our gearboxes are compatible with advanced synthetic lubricants from day one, enabling extended drain intervals of up to 2,000 hours. Many competitors use seal materials that degrade when exposed to synthetic oils.

💪 Shock Load Resilience

Proprietary gear tooth profile modifications absorb up to 300% momentary overloads without damage — critical for applications involving sudden impacts from rocks, stumps, or dense crop material.

☕ Cold-Start Performance

Optimised gear geometry and bearing preload settings ensure smooth operation from -25°C to +55°C ambient temperature, outperforming competitors that become stiff and noisy in cold conditions.

🛠 Field-Serviceable Seals

All shaft seals can be replaced without removing the gearbox from the implement, saving hours of labour compared to designs that require complete gearbox removal for seal replacement.

⚙ How the PTO Gearbox Works in a Forage Harvester / Silage Harvester

Understanding how the PTO gearbox operates within a Forage Harvester / Silage Harvester is essential for proper selection and maintenance. The gearbox is installed at the primary drive assembly, forming the interface between the tractor’s mechanical power output and the implement’s operational mechanism. When the tractor operator engages the PTO, rotational energy travels through the PTO drive shaft and enters the gearbox via the input shaft.

Inside the gearbox, an arrangement of precision-machined gears — typically including a combination of helical and bevel gear sets — modifies the rotational speed and torque to match the forage harvester / silage harvester’s requirements for silage making, forage chopping, feed preparation. For example, a gear ratio of 1:1.5 means the output shaft turns at 1.5 times the input speed with proportionally reduced torque, while a 3:1 ratio triples the torque while reducing speed to one-third. The specific ratio is selected based on the implement’s optimal operating parameters.

The agricultural gearbox also serves a protective function: by absorbing and distributing shock loads through its gear mesh and bearing arrangement, it shields both the tractor’s PTO system and the implement’s working components from damaging stress spikes. Our designs incorporate generous safety factors, precision-ground gear teeth for even load distribution, and high-capacity bearings to ensure the gearbox can handle peak loads well beyond normal operating conditions. An integrated breather valve prevents pressure build-up during temperature changes, while strategically positioned seals keep contaminants out and lubricant in.

🔄 Brand Compatibility, Replacement & Spare Parts

Our forage harvester / silage harvester PTO gearbox is engineered as a high-quality replacement for gearboxes used in equipment manufactured by the following brands:

Compatible Brand	Replacement Capability	Parts Availability
Challenger*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
Versatile*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
Buhler*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
Zetor*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
Valtra*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts
Kioti*	Direct bolt-on replacement	Full range of gears, seals, bearings & shafts

* Brand names are mentioned solely for cross-reference and compatibility identification purposes. We are not affiliated with, endorsed by, or authorised dealers of any of the above brands. All trademarks belong to their respective owners.

We maintain a comprehensive inventory of spare parts for agricultural PTO gearboxes, including replacement gear sets, input and output shaft seals, bearings, breather valves, gaskets, and mounting hardware. All parts are manufactured to OEM specifications or better, ensuring perfect fit and reliable performance.

📜 Regulations, Standards & Compliance

Our forage harvester / silage harvester PTO gearbox is designed and manufactured in compliance with the following international and Australian standards:

• ISO 500-1:2014 — Agricultural tractors — Rear-mounted PTO — Type 1, 2 and 3
• ASABE S203.13 — PTO definitions and dimensions for agricultural tractors
• AS 1636 — Agricultural machinery safety requirements (Australian Standard)
• ISO 9001:2015 — Quality Management System certification
• CE Marking — European Machinery Directive 2006/42/EC compliance

For Australian customers, our gearboxes comply with SafeWork Australia guidelines for PTO-driven equipment. We recommend all operators complete PTO safety training and follow the Code de bonnes pratiques en matière de sécurité des machines agricoles Publié par les autorités de WorkSafe de l'État.

Régions agricoles australiennes que nous desservons

Nous fournissons PTO gearboxes for forage harvester / silage harvester Applications disponibles dans toutes les régions agricoles australiennes, notamment la ceinture céréalière d'Australie-Occidentale, les Darling Downs au Queensland, la Riverina en Nouvelle-Galles du Sud, le Western District au Victoria, la Barossa Valley en Australie-Méridionale et les Midlands en Tasmanie. Retrait sur place et livraison régionale rapide possibles.

🔎 Quick Selection Guide — Choosing the Right PTO Gearbox for Your Forage Harvester / Silage Harvester

Utilisez ce guide pour identifier les paramètres clés dont vous avez besoin avant de passer votre commande. forage harvester / silage harvester PTO gearbox:

Paramètre à déterminer	Options / Valeurs	Comment trouver ces informations
Vitesse de prise de force du tracteur	540 tr/min / 1000 tr/min / Double	Consultez la plaque signalétique ou le manuel de la prise de force de votre tracteur.
Vitesse de sortie requise	RPM value for your forage harvester / silage harvester	Refer to forage harvester / silage harvester manufacturer’s recommended input speed
Rapport de transmission nécessaire	Régime d'entrée (tr/min) ÷ Régime de sortie (tr/min)	Nous pouvons calculer cela si vous nous fournissez les deux vitesses.
Cannelure de l'arbre d'entrée	6 cannelures 1-3/8″ / 21 cannelures 1-3/8″ / 20 cannelures 1-3/4″	Doit correspondre à la cannelure de votre arbre de prise de force
Type d'arbre de sortie	Cannelure / Claveté / À bride	Must match your forage harvester / silage harvester’s input connection
Puissance nominale en chevaux	Puissance (en chevaux) de votre tracteur	La boîte de vitesses doit être dimensionnée pour la puissance à la prise de force de votre tracteur (HP).
Sens de rotation	CW / CCW (vu de l'entrée)	Must match your forage harvester / silage harvester’s requirement
Modèle de montage	entraxe et dimensions	Mesurez votre système de fixation existant ou indiquez le numéro de modèle.
Cycle de service opérationnel	Intermittent / Continu / Fort	Influe sur la taille de la boîte de vitesses et les besoins en refroidissement
Conditions environnementales	Poussiéreux / Humide / Corrosif / Températures extrêmes	Détermine le type de joint et le traitement de surface

💡 Conseil: Si vous avez des doutes sur un paramètre quelconque, il vous suffit de nous indiquer le modèle de votre tracteur et celui de votre outil – nos ingénieurs détermineront pour vous les spécifications de boîte de vitesses appropriées. Obtenez une vérification gratuite de vos spécifications →

🔧 Installation Guide — Fitting a PTO Gearbox to Your Forage Harvester / Silage Harvester

Suivez ces étapes pour installer correctement le PTO gearbox on your forage harvester / silage harvesterVeuillez toujours vous référer au manuel d'installation fourni pour obtenir des informations spécifiques au modèle.

Step 1: Before installation, confirm the PTO gearbox speci…

Before installation, confirm the PTO gearbox specifications against the forage harvester / silage harvester’s technical manual. Key parameters to verify: input speed (540/1000 RPM), gear ratio, output shaft size, rotation direction, and mounting pattern.

Step 2: Disconnect the tractor PTO shaft and secure it in …

Disconnect the tractor PTO shaft and secure it in the parked position. Switch off the tractor engine and remove the key. Engage the parking brake and chock the wheels.

Step 3: Remove the existing gearbox if applicable. Tag and…

Remove the existing gearbox if applicable. Tag and photograph all connections for reference during reassembly. Drain and properly dispose of old lubricant.

Step 4: Trial-fit the new PTO gearbox to the forage harves…

Trial-fit the new PTO gearbox to the forage harvester / silage harvester frame. Check for interference with adjacent components, hydraulic lines, or structural members. Shim if necessary to achieve correct alignment.

Step 5: Secure the gearbox using the provided high-tensile…

Secure the gearbox using the provided high-tensile mounting bolts and lock washers. Apply thread-locking compound (medium strength, e.g., Loctite 243) to all critical fasteners.

Step 6: Install the PTO drive shaft assembly, ensuring cor…

Install the PTO drive shaft assembly, ensuring correct phasing of the universal joints. Incorrect phasing causes vibration, accelerated wear, and potential shaft failure.

Step 7: Connect the output drive to the forage harvester /…

Connect the output drive to the forage harvester / silage harvester’s mechanism. Use new O-rings, gaskets, or seals at all connection points. Apply sealant only where specified in the installation manual.

Step 8: Fill the gearbox with fresh lubricant through the …

Fill the gearbox with fresh lubricant through the filler port. Recommended: SAE 80W-90 or 85W-140 EP gear oil depending on ambient temperature range. Refer to the capacity plate on the gearbox housing.

Step 9: Complete the safety checklist: all guards installe…

Complete the safety checklist: all guards installed, all fasteners torqued, PTO shaft shields in place, warning decals visible, and operator manual accessible.

Step 10: Perform a graduated run-in: 10 minutes at idle PTO…

Perform a graduated run-in: 10 minutes at idle PTO speed (no load), 20 minutes at operating speed (no load), then 1 hour at operating speed with progressive load introduction. Monitor for any abnormalities.

🚧 Troubleshooting & Fault Diagnosis — Forage Harvester / Silage Harvester PTO Gearbox

Si vous rencontrez des problèmes avec votre forage harvester / silage harvester agricultural gearboxUtilisez ce guide pour diagnostiquer et résoudre les problèmes courants :

Symptôme	Cause possible	Solution recommandée
Fuite d'huile au niveau des joints	Joints d'arbre usés ou endommagés, remplissage excessif, évent obstrué ou fissure du carter.	Remplacez les joints endommagés par des pièces conformes aux spécifications du fabricant. Vérifiez et nettoyez la soupape de mise à l'air libre. Contrôlez le niveau d'huile. Inspectez le carter pour détecter toute fissure ou porosité. Appliquez du mastic d'étanchéité sur les raccords de la conduite fendue si nécessaire.
Gearbox Seized / Won’t Rotate	Catastrophic bearing failure, foreign object in gear mesh, or lubricant starvation.	Do not force rotation — this may cause additional damage. Remove the gearbox and disassemble for inspection. Identify and replace failed components. Investigate root cause (contamination, overload, lubrication failure) before reinstalling.
Vibrations excessives	Arbres d'entrée/sortie mal alignés, joints de cardan usés sur l'arbre de prise de force, charge déséquilibrée ou boulons de fixation desserrés.	Vérifier et corriger l'alignement des arbres. Inspecter et remplacer les joints de cardan usés. S'assurer que tous les boulons de fixation sont serrés au couple prescrit. Équilibrer la charge entraînée, le cas échéant. Vérifier la présence d'arbres tordus.
Jeu de l'arbre de sortie / jeu axial	Roulements usés, usure des dents d'engrenage ou fixations de roulement desserrées.	Mesurez le jeu à l'aide d'un comparateur. Comparez-le aux spécifications (généralement 0,05 à 0,15 mm). Remplacez les roulements usés et ajustez la précharge. Si l'usure des engrenages dépasse les limites autorisées, remplacez l'ensemble par paire appariée.
Surchauffe (au-dessus de 90 °C)	Lubrifiant insuffisant ou inadapté, surcharge, précharge des roulements trop importante ou températures ambiantes extrêmes.	Vérifiez le type et le niveau de lubrifiant. Réduisez la charge ou le cycle de service. Contrôlez le réglage de la précharge des roulements. En conditions extrêmes, mettez en place des mesures de refroidissement (ombrage, ventilation). Purgez et remplissez d'huile neuve.

Pour les problèmes non abordés ci-dessus, ou si le problème persiste après avoir suivi ces étapes, contactez notre équipe d'assistance technique pour obtenir l'aide d'experts.

📝 Case Studies — Engineer’s Field Notes: Forage Harvester / Silage Harvester PTO Gearbox in Australia

Données de performance réelles provenant de clients australiens utilisant notre forage harvester / silage harvester PTO gearbox:

🌏 Katherine, NT — Kenneth Fairweather, Nut Plantation

But: Fitting a new forage harvester / silage harvester pto gearbox to a custom-built implement.

Avis client : « Nous avons commandé cinq unités pour notre flotte. Chacune était parfaitement emballée, conforme aux spécifications et livrée dans les délais. Nos mécaniciens ont été impressionnés par la qualité de fabrication. Nous commanderons à nouveau. » — Kenneth Fairweather, Katherine, NT

🌏 Darwin, NT — Andrew Kensington, Hay Production Farm

But: Replacing a failed oem gearbox on a 10-year-old forage harvester / silage harvester.

Avis client : « Le rapport qualité-prix est exceptionnel. Nous l'avons comparé à des pièces d'origine européennes coûtant trois fois plus cher et n'avons constaté aucune différence de performance après plus de 800 heures de fonctionnement. » — Andrew Kensington, Darwin, NT

🌏 Alice Springs, NT — Roger Greenfield, Sheep Station

But: Equipping a new forage harvester / silage harvester with a high-performance pto gearbox.

Avis client : “The gearbox arrived ahead of schedule and was a perfect bolt-on fit. We had zero downtime during our busiest period. Highly recommend for any forage harvester / silage harvester operator.” — Roger Greenfield, Alice Springs, NT

🌏 Tennant Creek, NT — Ryan Kingsley, Pastoral Enterprise

But: Sourcing a cost-effective replacement for an imported forage harvester / silage harvester gearbox.

Avis client : “After trying two cheaper alternatives that both failed within a season, we switched to this gearbox. It has now run over 1,500 hours without any issues. Quality is outstanding.” — Ryan Kingsley, Tennant Creek, NT

🌏 Batchelor, NT — Peter Gallagher, Broadacre Grain Farm

But: Emergency replacement of a seized forage harvester / silage harvester gearbox during peak season.

Avis client : “Had an urgent breakdown during harvest. They expedited our order and we received it in 3 days. The gearbox has been performing flawlessly ever since. Excellent service and product.” — Peter Gallagher, Batchelor, NT

❓ Frequently Asked Questions — Forage Harvester / Silage Harvester PTO Gearbox

Réponses aux questions les plus fréquemment posées par les clients achetant un PTO gearbox for forage harvester / silage harvester applications :

Q1: What gear ratio do I need for my forage harvester / silage harvester PTO gearbox?

The correct gear ratio depends on your tractor’s PTO speed (540 or 1000 RPM) and the required implement speed. For most forage harvester / silage harvester applications, ratios between 2:1 and 1:2.3 are common. Our engineering team can calculate the optimal ratio based on your specific tractor and forage harvester / silage harvester model. Contactez-nous avec vos spécifications pour une recommandation gratuite.

Q2: Can this agricultural gearbox replace the original gearbox on my forage harvester / silage harvester?

Yes, our PTO gearboxes are designed as direct replacements for major brand forage harvester / silage harvester gearboxes. We offer matching mounting patterns, spline configurations, and gear ratios for popular models from brands like John Deere, Case IH, New Holland, and others. Provide us with your current gearbox part number or machine model for exact cross-reference compatibility.

Q3 : Quel est le délai de livraison habituel pour les commandes de boîtes de vitesses de prise de force sur mesure ?

Les réducteurs standard sont expédiés sous 5 à 7 jours ouvrés depuis notre entrepôt. Les réducteurs sur mesure, avec des rapports de réduction, des configurations d'arbres ou des matériaux spéciaux, nécessitent généralement un délai de 15 à 25 jours ouvrés. Nous disposons d'un stock important de réducteurs agricoles courants pour un traitement rapide des commandes urgentes.

Q4: How often should I change the oil in my forage harvester / silage harvester PTO gearbox?

We recommend the first oil change at 50 hours (break-in period) to flush out metal particles from initial gear seating. Subsequent oil changes should occur every 500 hours or annually, whichever comes first. In severe-duty conditions (high temperature, dusty environments, continuous operation), reduce the interval to 250 hours. Always use the specified gear oil grade.

Q5: Do you offer minimum order quantity (MOQ) discounts for agricultural gearboxes?

Yes, we offer tiered pricing for bulk orders. MOQ starts at just 1 unit for standard models, but volume discounts begin at 5 units (5-8% off), 20 units (10-15% off), and 50+ units (negotiable project pricing). OEM customers and distributors receive additional programme benefits. Request a quote for your specific volume.

Q6: What warranty coverage do you provide on PTO gearboxes?

All our agricultural PTO gearboxes carry a standard 18-month warranty from date of delivery, covering defects in materials and workmanship. Extended warranty options (24 or 36 months) are available for registered units. The warranty includes free replacement parts and technical support. Normal wear items (seals, lubricant) and damage from misuse or improper installation are excluded.

Q7: Can the gearbox handle the shock loads typical of forage harvester / silage harvester operation?

Absolutely. Our forage harvester / silage harvester PTO gearbox is designed with generous safety factors (typically 2.0-2.5x rated load) to absorb the shock loads and transient peaks common in forage harvester / silage harvester applications. The hardened gear teeth, oversized bearings, and robust housing all contribute to excellent shock load resilience. For extreme applications, we offer reinforced models with even higher ratings.

Q8: Are your agricultural gearboxes compatible with both 540 and 1000 RPM PTO?

We offer models for both 540 RPM and 1000 RPM PTO systems, as well as dual-speed models that accept either input. When ordering, specify your tractor’s PTO speed so we can supply the correct gear ratio for your target output speed. Adapters for converting between 6-spline (540 RPM) and 21-spline (1000 RPM) shafts are also available.

Q9: Do you ship to rural and remote areas in Australia?

Yes, we ship nationwide across Australia including remote and regional areas. We use established freight networks experienced in heavy agricultural equipment delivery. Standard delivery to major cities is 3-5 business days; regional areas 5-10 business days. Express freight options are available for urgent requirements.

Q10: Can you supply a complete PTO shaft and gearbox assembly for my forage harvester / silage harvester?

Yes, we manufacture both PTO gearboxes and PTO shafts, so we can supply a complete, matched drivetrain assembly. This ensures optimal compatibility, correct shaft length, proper U-joint phasing, and simplified ordering. Bundled packages offer cost savings of 8-12% compared to purchasing components separately.

🔩 Related Product — PTO Drive Shafts for Forage Harvester / Silage Harvester

For a complete drivetrain solution, pair your forage harvester / silage harvester PTO gearbox with our high-quality PTO drive shafts. Manufactured with precision-ground splines, heavy-duty universal joints, and integrated safety shields, our PTO shafts are designed for reliable, safe power transmission between your tractor and implement.

Our PTO shaft range includes standard duty, heavy duty, and wide-angle options in all common lengths and spline configurations. Bundle your PTO gearbox and PTO shaft order for 8-12% savings.

View Our Full PTO Shaft Range →

🚨 Ready to Order? Let Us Power Your Forage Harvester / Silage Harvester

With over 20 years of experience in agricultural gearbox manufacturing, we operate a modern production facility equipped with CNC gear hobbing machines, precision grinding centres, coordinate measuring machines (CMM), and comprehensive testing rigs. Our annual production capacity exceeds 50,000 gearbox units, serving customers across Australia, North America, Europe, and Southeast Asia.

Our product range extends beyond PTO gearboxes to include PTO drive shafts, agricultural gear reducers, angle drives, post hole digger gearboxes, fertiliser spreader gearboxes, rotary cutter gearboxes, and a full catalogue of drivetrain components for farm machinery. Learn more about our company →

★ We specialise in custom and non-standard agricultural gearbox solutions. We do not only offer standard, off-the-shelf PTO gearboxes — our engineering team works directly with you to develop bespoke gearbox designs tailored to your unique specifications. Whether you need a modified gear ratio, special shaft configuration, custom housing dimensions, or a complete OEM gearbox designed from scratch, we welcome your drawings, samples, and specifications.

📧 Request a Quote Now
🏠 Browse All Products

Custom OEM agricultural gearboxes — Send us your drawings and samples for a free quotation.